Mossberg 500 Wood Forend Original

• For Glock 26 9MM Finger Extension Floor Base Plate Black
• 1000+ High Resolution Permanent Laser engraved images, will not rub off, not painted, custom engraving too – by NDZ Performance
• 100% Aircraft Grade T6 Billet Aluminum, Mil-spec Hardcoat Anodized Durable Finish
• Replaces Stock Plastic Plate with a Durable Aluminum piece, Easy Install, Requires NO Modifications
• Designed and Made In America, In Our Facility – In NDZ Packaging

• Cartridge shell case size: Length is 6″. Width is 1″. Height is 4″.
• Close style ammo cartridge holder is made of quality waterproof nylon. Shooter`s pouch is equipped with 2 rows of elastic loops for 12 or 16 gauge shells and may accommodate up to 12 cartridges.
• This shotgun ammo wallet has two loops at the back to fix it on the belt. Accommodates belts up to 2 1/4 -Inch wide.
• Classic ammo holder for shotgun shells closes with snap buttons to keep your cartridges safe and dry.
• Belt ammo pouch is easy to clean and will keep rounds at hand.

If you want your shots to be on target at long ranges, you need to have your crosshairs leveled perfectly. Some alignment tools on the market level the crosshairs to the scope base or another arbitrary and inconsistent point. The Level-Level-Level scope crosshair alignment tool from Wheeler Engineering is a far better option.It works by aligning your scope with the top of the receiver, which is the most accurate point. The leveling can be done in minutes with this tool. You simply attach the first level to the receiver, place the other level on any flat point on top of the scope, and orient the scope so that the two levels match up! It fits most popular bolt action rifles, and it can be adjusted to fit more obscure designs.

This item features: -Specially formulated paint in stick form designed to color-brighten stamped or engraved lines and lettering. -Paint stays flexible, expands and contracts with the surface. -Contains no solvents. -Long-lasting will not rub off or smear. -No mess or waste, eliminates dripping brushes and paint spills. -Temp. Range: -50.0 F [Min], 150.0 F [Max]. -Applicable Materials: Metal, Plastic, Ceramics, Wood, Rubber, Glass. Meets U.S.A. federal specification TT-F-325a I and MIL-STD 171.

• 48.5″ x 156.5″ x 10″
• Fits both DA/SA models with decocker lever, AND DAK models without decocker lever and hammer spur
• Fits 9mm, 357SIG or .40 cal guns
• Will NOT fit the Allround models and the 226 Legion
• Manufactured from a soft durable rubber and features a lightweight, synthetic skeleton insert that makes up the rigid interior of the handle

Recoil buffers are an easy and inexpensive way to eliminate damage of critical components by preventing the metal to metal contact of the slide or breech block with the frame. Made from a high density polyurethane formulated for maximum shock-absorbing characteristics, the recoil buffer is a drop-in part.The CZ recoil buffer will eliminate the metal to metal impact of the slide on the receiver each time the weapon is fired. You will extend the service life of your pistol as well as have reduced felt recoil by installing one in your weapon. Installation is easy and requires no special tools or modification to your gun.

The Choate Flash Hider and Front Sight for the Ruger Mini-14 fits most 580 and higher series rifles. For use on rifles with a barrel diameter of 0.625″, make sure to measure the barrel before you order, some of the early 580 series rifles have the smaller 0.562″ barrel. The compensator is attached to the gun barrel by a 1/8 inch spring steel roll pin. Gunsmith installation recommended to drill hole for roll pin.

Hogue rubber grips are molded from a durable synthetic rubber that is not spongy or tacky, but gives that soft recoil absorbing feel, without effecting accuracy. This modern rubber requires a completely different molding process than ordinary neoprene and results in a much superior grip. The material used does not come apart or deteriorate and is resistant to all solvents and oils used around firearms.

GLOCK OEM factory Recoil Spring Assembly fits G19, G23, G32, G38 (marked 5593 on end of recoil spring guide). For Generation 1, 2, and 3 pistols.