Win 1300 Pistol Grip by Adv Tech#TFS0600

Recoil buffers are an easy and inexpensive way to eliminate damage of critical components by preventing the metal to metal contact of the slide or breech block with the frame. Made from a high density polyurethane formulated for maximum shock-absorbing characteristics, the recoil buffer is a drop-in part.The CZ recoil buffer will eliminate the metal to metal impact of the slide on the receiver each time the weapon is fired. You will extend the service life of your pistol as well as have reduced felt recoil by installing one in your weapon. Installation is easy and requires no special tools or modification to your gun.

TALON Grips are textured, stick-on gun grips that help you get a secure hold on your firearm improving performance, safety, and confidence so you maintain control. Installation is quick and easy. The pistol grips will not move or shift once installed, however, they can be removed cleanly at any time, returning your pistol to original factory condition. You can expect 1 to 3 or more years of benefits from a TALON Grip.

The Choate Flash Hider and Front Sight for the Ruger Mini-14 fits most 580 and higher series rifles. For use on rifles with a barrel diameter of 0.625″, make sure to measure the barrel before you order, some of the early 580 series rifles have the smaller 0.562″ barrel. The compensator is attached to the gun barrel by a 1/8 inch spring steel roll pin. Gunsmith installation recommended to drill hole for roll pin.

• Cartridge shell case size: Length is 6″. Width is 1″. Height is 4″.
• Close style ammo cartridge holder is made of quality waterproof nylon. Shooter`s pouch is equipped with 2 rows of elastic loops for 12 or 16 gauge shells and may accommodate up to 12 cartridges.
• This shotgun ammo wallet has two loops at the back to fix it on the belt. Accommodates belts up to 2 1/4 -Inch wide.
• Classic ammo holder for shotgun shells closes with snap buttons to keep your cartridges safe and dry.
• Belt ammo pouch is easy to clean and will keep rounds at hand.

Blaser sling swivel loop and pivot pin/screw.

Fits all Blaser rifles with fixed studs and will suit straps of up to 20mm x 3.5mm

• The Hi-Lift 48 inch all-cast jack is constructed with cast iron components for ultimate strength and durability. Hi-Lift Jacks are the only all-cast jacks manufactured in the world.
• Top winch connector clamp and powder coated finish with zinc-plated hardware standard on all jacks
• Two piece handle and socket is durable and reliable
• Safe use information stickers, including rated load details and operating instructions, affixed to handle
• For greater safety, all Hi-Lift jacks are equipped with a shear bolt which prevents the jack from being used on loads greater than 7000 pounds

The extended magazine release allows for a quick release of factory

magazines. Simply reach in front of the trigger guard and push forward,

no more having to push up on the factory release. It extends .550″ down

from the trigger guard housing designed not to interfere with benchrest

or sandbags during shooting. The extended magazine release is completely

CNC-machined from billet material – no castings.

• 48.5″ x 156.5″ x 10″
• Fits both DA/SA models with decocker lever, AND DAK models without decocker lever and hammer spur
• Fits 9mm, 357SIG or .40 cal guns
• Will NOT fit the Allround models and the 226 Legion
• Manufactured from a soft durable rubber and features a lightweight, synthetic skeleton insert that makes up the rigid interior of the handle

This item features: -Specially formulated paint in stick form designed to color-brighten stamped or engraved lines and lettering. -Paint stays flexible, expands and contracts with the surface. -Contains no solvents. -Long-lasting will not rub off or smear. -No mess or waste, eliminates dripping brushes and paint spills. -Temp. Range: -50.0 F [Min], 150.0 F [Max]. -Applicable Materials: Metal, Plastic, Ceramics, Wood, Rubber, Glass. Meets U.S.A. federal specification TT-F-325a I and MIL-STD 171.